Professional chemical products supplier

Dandong import contact adhesive

by:Sinograce Chemical     2021-03-14
Dandong imported adhesive contact dandong adhesive contact with polyacrylate is used much, its production has more than natural rubber pressure-sensitive adhesive. Use hot melt adhesive sealing speed, the bonding process only need 1 ~ 3 seconds to complete, suitable for mass production, less energy consumption, low cost. Standard corrugated carton sealing of hot melt adhesive costs about 32 1000 yuan/box, this is the middle of the hot melt adhesive price, and tape seal in the middle of the price is about 120 yuan / 1000 cases. ( 2] Performance measurement requirements type editor CS501 super constant temperature trough, D25 - Type electric mixer, speed controller, oven, balance, three flask, drip tube, thermometer, beaker, measuring cylinder, pipette, washing ears ball, Fourier infrared spectrometer in spite of the existing reactive flame retardant effect is limited, but the reactive acrylate pressure-sensitive adhesive performance still has a lot of advantages in various aspects, flame retardant pressure sensitive adhesive huge market for its research and development also brings a lot of power. In addition to using conventional adhesive parts structure adhesive, due to the ship sailing in the special environment, lake and sea, also use large amounts of adhesive/sealant to seal, liquid polysulfide sealant used for filled structure joint, so as to solve the joints airtight problem by wood swelling. If use hot melt adhesive, highly processed adhesive will not cause downtime; While replacing tape need downtime. And, in the box is not installed clapboard, sealing strength is greater than that of using tape sealing with diaphragm sealing intensity, can reduce the cost of diaphragm. 2, polyurethane hot melt adhesive machine, when to take off the bucket, filling the air pressure should be from small to large pressure slowly, under no circumstances do not allow direct use of high pressure gas directly to take off the barrel, avoid the accident. Aircraft manufacturing is also widely used sealants, especially seal tank of polysulfide sealing materials. The selection of the hot melt adhesive: dandong import adhesive contact note product features appearance milky white or light yellow latex adjust the indicators, this product according to the laminating process when using do not add water or other solvents work to maintain good health habits 20 kg, 50 kg bottled product features look milky emulsion (2) resin pressure-sensitive adhesive used this kind of pressure sensitive adhesive resin of polyacrylic acid ester, pu, PVC, polyvinyl ether, etc. With the characteristics of chemical resistance and easy to repair. At present, the domestic do adhesive manufacturers have thousands of home, in front of the interests of many businesses shoddy, and hot melt adhesive with different affinity of different adhesive materials. In order to make better play to the 'sticky' hot melt adhesive, adhesive industry experts warm reminder, when choosing hot melt adhesive should carefully consider the following factors: in printing ink, glue, printing ink, the unit price is based on the quality of the ink, glue, glue viscosity and concentration to measure the comprehensive cost and the size of the price, because the printing factory can't identify the several indicators, to purchase ink, glue difficult. 1) Healthy environmental protection: inferior hot melt adhesive often USES recycled materials or inferior raw material, or in the process of the system of plastic formation pollution, or process defect cause gum is not pure, hot melt adhesive containing solvents prone to make finished products or impurity moisture or easy to volatile substances. For the food industry, are lethal damage. Dandong import contact adhesive ( 1) Adjust the structure under the premise that guarantees the stability of the emulsion, the content of hydrophilic group as low as possible, can improve the water resistance of the film; These series of products used in automobile electronic components, fixed component adhesive, filling and sealing, which can effectively improve the seismic resistance of products. 3, move or lift the polyurethane hot melt adhesive machine, only allow you to use the base as handling, may not take advantage of the stroke cylinder pur hot melt glue machine, electrical appliances, electrical components on the control panel or the door is insulated pipeline plastic pipes for auxiliary and to raise the hot melt adhesive machine, improper handling can damage pur hot melt adhesive machine spraying equipment. 2) Color: by the color of the adhesive material is different, color requirements for hot melt adhesive should differ. If it be adhesive content itself to the color no special requirements, it is recommended to use yellow hot melt adhesive, generally speaking, yellow hot melt adhesive is better than white sticky. Environmental protection, high efficiency, low cost, simple process of the development of the reactive flame retardant has great prospects for development. No matter when ship assembly is glass fiber reinforced plastic, wood or metal structures are used adhesive. Dandong import contact adhesive
Anhui Sinograce Chemical Co., Ltd. is committed to fulfill the demands of our customers with using chemical company.
Anhui Sinograce Chemical Co., Ltd.’s mission is to be the leading global innovator, developer and provider of chemical company chemical factory products, systems, and services.
Anhui Sinograce Chemical Co., Ltd.'s main technology of chemical company leads us to understand and utilize information correctly.
To properly understand what customers want, when, why and how they want it, Anhui Sinograce Chemical Co., Ltd. needs to pivot toward sentiment analysis, a burgeoning technology that taps into consumer demand based on natural language processing.
Anhui Sinograce Chemical Co., Ltd. has unique staffs who will serve you with their best ideas by affording you with high-quality service.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...