Professional chemical products supplier

Hengyang industry adhesive agent

by:Sinograce Chemical     2020-12-08
Hengyang industry adhesive agent of hengyang industry adhesive agent if you are unwell seek immediate emulsion type and solvent type and hot melt pressure sensitive adhesive. Fourth, resistance to temperature. Hot melt adhesive is more sensitive to temperature. The temperature reached a certain degree, hot melt adhesive began to soften, below a certain temperature, hot melt adhesive will become fragile, so choose hot melt adhesive must fully consider the product's environmental temperature change. Its advantage is good film forming, good color fastness, PU can stick hot glue, is the current commonly used coating glue. Five, sticky. Hot melt adhesive viscosity points late early viscosity and viscosity. Only late early viscosity and viscosity is consistent, can make the hot melt adhesive and then remained stable. In the process of production of hot melt adhesive, shall guarantee that the oxygen resistance, brine resistance, resistance to acid, alkali and a plastic. Being the different material, and then play by hot melt adhesive viscosity is also different, therefore, should choose according to different material different hot melt adhesive. Hengyang industry adhesive agents used tools before drying of glue can be used warm water to clean. 1, can under the professional instrument for testing analyzing the composition of hot melt adhesive, so that we can get the accurate data. Varieties of modified according to the provisions of GB/T 4851. (5) cleaning fluid applications covered non-metallic containerized, many soak glue brush, cleaning fluid containing resin (more Color becomes very white) And should be replaced; Acrylic pressure sensitive adhesive general is given priority to with solution type, there are few is water-based pressure-sensitive adhesive, hot melt pressure sensitive adhesive main composition of acrylic can serve as a soft monomer and hard monomer, functional monomer composition of the three. The way such as mixing, grafting of existing varieties were modified to improve the performance of hot melt adhesive. Such as stabilizing agent to prevent oxidation; Tackifier improve bonding strength; Paraffin reducing viscosity change surface properties; All kinds of fillers can improve the viscosity and melting point and bonding strength, etc. To study various varieties, dosage, chelating agent and formula optimization to meet different needs. ( 2] 10, when pur hot melt adhesive machine heating platen press into the new polyurethane plastic barrels, should open the glue valve, complete discharge residual air in the plastic bucket, and will take the air bubbles pur hot melt adhesive ruled out clean, avoid polyurethane hot melt adhesive with air into the pump body and the hot melt adhesive machine in the throat. Defect is poor film-forming, washing fastness, pu can't stick hot glue. Adhesive agent used in accordance with the factory, new product development of hengyang industry synthesis process is generally described as: feeding vacuum and nitrogen charging before ~ ~ ~ to block heat booster to the holding to put pressure to keep the normal pressure to vacuum and nitrogen charging and discharging after dicing to drying to packaging. Defect is due to the use of the oily solvent, so environmental protection lacking a bit, especially now that oil prices, oil solvent prices soaring all the way, most of the coating glue due to the cost is too high, so use more bad of the oily solvent, leading to environmental protection is not up to standard, in addition with the national environmental standards to further improve, so for environmental requirements of the coating adhesive is higher and higher. Hot melt adhesive and curing functional hot melt adhesive are two major types of new product on the market. The former main characteristic is that improve the hot melt adhesive high temperature resistant characteristics, improve the softening point to more than 120 ℃, thus expanding the scope of its use; Functional hot melt adhesive is for a particular occasion, can realize specific functions to meet the needs of all aspects. Such as water soluble or decentralized hot melt adhesive, hot melt sealant, hot melt pressure sensitive adhesive and so on. Below is the hot melt sealant. It is a kind of polyisobutylene rubber as basic material of one-component, solvent free, not out of the fog, sulfide, has a permanent plastic insulating glass sealant. Hot melt butyl sealant in relatively wide temperature range its plasticity and sealing, and the surface cracks, the same hard. It on the glass, aluminum alloy, galvanized steel, stainless steel and other materials have good adhesive properties. Due to its extremely low water vapor transmittance, it can form a with elastic sealant excellent resistance to moisture system. Characteristics: good sealing effect, easy quality assurance; Without curing period, save area; Is environmental protection product, the use of no waste, clean environment; Save time, raw materials, personnel, reduce the production cost. Hengyang industry adhesive agent
is a modern chemical company widely used in chemical factory industry. It also enhances the quality chemical factory value of the products.
Anhui Sinograce Chemical Co., Ltd. offers the best products, high-quality services and innovative technology.
chemical factory chemical company is one of the most commonly used tool for chemical factory.
We are proud to be a part of helping you to make healthy choices to last a lifetime. Check out our website to see all chemical factory chemical company products we offer at Sinograce Chemical. If you want to start that road to be better, contact us today!
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...