Linyi henkel water-based glue factory linyi henkel water-based glue factory use matters when it comes to hot melt adhesive
machine application in various industries, make our related industry to a higher stage of development, production and related operators configuration has changed too.
(1) the fabric paste with hot melt adhesive is due to the consumption of silica gel after refining and sterilization, can be directly when mixed with food according to the requirement and guarantees the drying of food and food to eat together, but without any poison to the human body.
Furniture furniture USES hot melt adhesive is a kind of special to the man-made plank paste adhesive, it is a kind of environmental protection, solvent-free thermoplastic rubber.
Adhesive for sewing can reduce labor intensity, garment and clothing made of fine, fit, strong strong.
Used in fabric paste mainly include polyamide hot-melt adhesive, such as cheese and polyurethane.
Edible silica gel pore size of about 8 -
10 nm, specific surface area, 300 -
500 m2 / g, and surface water, the water has very strong absorption ability, under the condition of high humidity the water absorbing capacity can amount to 80% of its weight
(3) : late because of the small water molecules than solvent-based adhesive, can penetrate into the surface of the material smaller pore, equivalent to cast anchor in the material surface, its late on and solvent adhesive, with some suitable for cast anchor porous materials, such as mesh cloth and EVA, the late strength is better than solvent-based adhesive;
(3) glue barrel stacked shall not exceed 4 layer;
Avoid direct sunlight and rain;
3 type water-based glue suitable shoes and shoes (4) the warehouse should be set temperature and humidity meter, advice within 5 ∽ 30 ℃, temperature control and record every day, such as the temperature is beyond the scope suggested, should take timely improvement measures, to ensure that the water-based adhesive
The rapid development of the electronics industry to drive the further development of conductive adhesive.
(2) the lining cloth processing with hot melt adhesive in the late 1970 s, hot melt adhesive to begin to enter to wood industry, used for sealing side, plywood core, plate joining together, such as furniture tenon joint, early hot melt adhesive equipment is mainly dependent on the United States, west Germany, Italy and other countries of the equipment, along with the hot melt adhesive equipment has become increasingly mature, stable, selection and use is suitable for the hot melt adhesive equipments of the furniture factory details, not only can improve the quality of the furniture and class, and can improve the production efficiency, reduce the difficulty of the panel is renovated, reduce labor intensity.
Adhesive lining cloth is on fabric surface evenly Xu Bu made of hot melt adhesive.
When used to adhesive lining cloth cut into the required shape and size, to be coated with hot melt adhesive side with other fabric materials (
On the back of the hot-pressing bonding.
It lining in the clothing layer, as a skeleton of a garment, simplifies the clothing processing technology and time, make the garment with light, beautiful, comfortable, insurance type, washable, durable effect.
The smell of the different enterprises have different testing standards, to simulate the hot melt adhesive application requirement is to smell method, such as the same amount of the same kind of hot melt adhesive in different size but same sealed in the jar, heated to a temperature point after how much time, take out the cooled to room temperature, open the lid and smell by testing personnel, it is concluded that the respective side value, record down, do three - over and over again
Five times, it is concluded that the average for the final test results.
Lining cloth processing general requirement for hot melt adhesive is a colorless, odorless, texture soft, rapid bonding, resistance to wet and dry wash, cannot have an effect on fabric, light resistance, etc.
Can use a variety of hot melt adhesive lining cloth processing, almost all types of hot melt adhesive can be used, with much is ethylene -
Vinyl acetate (
Hot melt adhesive, polyamide hot melt adhesive and high-pressure polyethylene (
Hot melt glue powder, and different USES of hot melt adhesive and processing methods are also different.
Linyi henkel water-based glue factory vinyl acetate copolymer (
(3) the carpet back glue with hot melt adhesive simple conductive adhesive and two basic performance has been unable to meet the requirements of electronic devices, also need more conductive adhesive has excellent properties of thickness: 0.
Melting temperature: 205 mm - 120
10-160 ℃ stress:
20 pounds per square inch hot melt time: 3 -
30 seconds main models: 3 m615, capa H192 TESA8475, TESA8432, thoughts, etc.
Linyi henkel water-based glue factory which the vast majority of cases is the use of ethylene.
chemical company has become a crucial product for marketers, especially when it comes to brand building and engaging potential customers.
If you are interested in , click Sinograce Chemical to see some items with features that you will be amazed at.
Getting chemical company from an idea to production is a complex process. It involves significant research, time, planning and patience. But with the right information, the right resources and the right product, it's possible.
chemical company developed from Anhui Sinograce Chemical Co., Ltd.’s unique skills in high technology has helped to produce chemical companychemical factory.