Longyan boss compound rubber prices longyan boss composite adhesive
The experiment reagent 4.
Latex solid content first made a small box, aluminum foil with electronic analytical balance according to its quality, record the value.
Glue dispensing quantity according to the work experience, the size of the adhesive dot diameter should be the half of bonding pad spacing, the size of the adhesive dot diameter should be adhesive dot diameter after patch 1.
Five times, so that can ensure that there is enough glue to bonding elements and avoid excessive glue bonding pad and glue machine dispensing quantity depends on the length of the rotation of the screw pump to decide, practice should be according to the production situation,
Room temperature, glue viscosity, etc. )
Selection of pump rotation time, manufacturing defects which were liable to occur during the following process: glue dot size is unqualified, wire drawing, glue impregnation welding plate, curing strength is bad off so easily, solving the problem of the glue machine should be various technique parameters, overall research to find a solution to the problem.
Let's look at the characteristics of offset printing ink, compared with the silk screen, printing ink layer thinner, thin will have a drawback, simple sense is bad, visual effect is weak, there would be no stereo effect.
Water-based coating glue with water as solvent or polyurethane acrylate resin through specialized emulsification equipment, emulsion.
Its advantage is: many varieties, environmental protection, low prices.
Now there are a lot of coating is done with water soluble glue, such as general water soluble pa, water soluble pu and leather adhesive, oil wax feeling, the feeling of color paste and other functional material.
Water soluble with its functional and environmental protection, and the price is low, will be the future direction of coating.
Defect is poor film-forming, washing fastness, pu can't stick hot glue.
Solids 50 + / - 2% health and safety of 20 kg, 50 kg bottled product use machine good adaptability, high peel strength, good ink, 礚 powder capability is strong, the early stick with a viscous fluid manner, can replace the existing solvent laminating adhesive used on dry laminating machine look pale yellow viscous emulsion should stir well when using stored in shady and cool place, avoid direct sunlight, keep the temperature is 5 ~ 40 ℃ industry use of pressure-sensitive adhesive are mainly four categories: solvent-based emulsion pressure sensitive adhesive, pressure-sensitive adhesive, hot melt pressure sensitive adhesive and radiation type of pressure sensitive adhesive.
Thin, of course, is not without its advantages, will ink consumption is small, not paper deformation caused by the contraction of the ink, little impact on product quality.
Oily coating adhesive is oily solvent (
Toluene, DMF, butanone, etc. )
As a solvent, dissolve or polyurethane acrylate.
Its advantage is good film forming, good color fastness, pu can stick hot glue, is the current commonly used coating glue.
Defect is due to the use of the oily solvent, so environmental protection lacking a bit, especially now that oil prices, oil solvent prices soaring all the way, most of the coating glue due to the cost is too high, so use more bad of the oily solvent, leading to environmental protection is not up to standard, in addition with the national environmental standards to further improve, so for environmental requirements of the coating adhesive is higher and higher.
Hot melt pressure sensitive adhesive.
Solid content, there are gap filling, to avoid the edge roll up, bubble and crack, and cause the glued parts deformation, dislocation and contraction.
Hot melt adhesive is a kind of plastic adhesives, to a certain temperature range with the temperature change and change its physical state, and chemical properties unchanged, its non-toxic tasteless, environmentally friendly chemical products.
Is the use of hot melt glue by heating the hot melt adhesive, hot melt adhesive machine melt glue after become a kind of liquid, by hot melt adhesive machine hot melt rubber hose and hot melt glue gun, to be adhesive surfaces, hot melt adhesive cooling after completed the glue.
Of course the advantage to play out of the hot melt adhesive in bonding, must use high quality hot melt adhesive and the corresponding quality reliable performance of hot melt adhesive machine to match them.
Longyan boss compound rubber prices don't have flooded floor or very humid environment of moisture in the pur reactive polyurethane hot melt adhesive machine maintenance.
Water-based glue process characteristics of longyan boss compound rubber prices in addition to the above several kinds of raw materials can also be according to the difference of temperature, regions with some suitable for cold with the temperature of the thermal dose of cold resistance agent or suitable for tropical temperatures.
7, if possible, try to stand in plastic carpet for maintenance work.
(1) using water-based glue, in line with the shoe industry, a long-term trend in brands actively, water-based adhesive
has been widely used all kinds of shoe factory, water-based glue quality gradually progress and stability;
Since the early 1970 s, polyurethane adhesive for the generation of polysulfide, used to install the windshield and rear window.
Longyan boss compound rubber prices again into the glue in a small box in the sample, according to its quality, record the value.
Anhui Sinograce Chemical Co., Ltd. specializes in undertaking corporate offers to cater the needs of different companies.
If you would like to learn more about , be sure to visit Sinograce Chemical for more information!
There are ample scientific evidence of reducing the risk of chemical factory.
By investing in an ethical supply chain, Anhui Sinograce Chemical Co., Ltd. position ourselves to engage with a driven, engaged customer base.