Professional chemical products supplier

Organosilicon series

Home  > PRODUCT  > Non Stick Coating  > Organosilicon series  > 

S-202 Silicone Marble-Coating

这里可以自定义设置
S-202 Silicone Marble-Coating
silicone kitchen utensils marble coating
As temperature resistance decorative non-stick coating, it could be used on outside of aluminum non-stick cookware. Please do complete applicability test for specific use
B站不支持收货地址
B站不支持库存规格
Model
S-202
MOQ
200kg
Payment
L/C, D/A, D/P, T/T, Western Union, MoneyGram, OA
Place of Origin
China Anhui
Brand
sinogracechist
参数暂无数据
多属性暂无数据
B站不支持优惠卷

Add success, do you want to check your shopping cart?

暂无分享
B站不支持产品保障
该产品后台详情无内容

SILICONE COATINGS
S-202
Silicone Marble-Coating

As temperature resistance decorative non-stick coating, it could be used on outside of aluminum non-stick cookware. Please do complete applicability test for specific use.

Typical Properties

TypeSilicone coating

Product model

S-202A (Primer)

S-202B (Dot-1)

S-202C (Dot-2)

Recommended dosage

10kg primer

0.5kg Dot-1: 0.5kg Dot-2

Appearance

Light brown (Primer)

Light yellow (Dot-1)

Black (Dot-2)

Solid content (%)

45±1 (Primer)

40±1 (Dot-1)

39±1 (Dot-2)

Viscosity (cp)

30~50 (Primer)

10~16 (Dot-1)

10~16 (Dot-2)

Density (g/ml)

1.20±0.20 (Primer)

1.25±0.20 (Dot-1)

1.25±0.20 (Dot-2)

pH

8~11 (Primer)

8~11 (Dot-1)

8~11 (Dot-2)

Gloss (60° glossimeter)

45-55

Film thickness (μm)

15-25

Hardness (ZHONGHUA pencil)

>3H

Adhesion (1mm*1mm)

Grade 1


Key Features

● Eco-friendly and PFOA free

● Showing the effect of natural marble

● Easy application process, with bright color

● It’ s workable at 200℃, good chemical resistance

APPLICATION

Outside of tensile aluminum and die-casting fry pan, wok, soup pot, etc. 

这里可以自定义设置

Storage and Handling

1. Requirement on pre-treatment

● Firstly, apply high-temperature degreasing, then wash with 1%~3% NaOH solution (60℃) for more than 6 minutes, dry it after water rinsing;
● Blast with 80#~120# corundum to make the surface roughness reach 2.0μ~3.0μ, pay attention to sandblast evenly;
● Wash with 1%~3% NaOH solution(60℃) for more than 6 minutes, rinse with water;
● Wash with 1%~3% hydrochloric acid solution (60℃) for more than 6 minutes, rinse with water and dry.

2.Preparation of the coating

● Dispersion of coating: the coating must be fully dispersed before operation;
● Viscosity adjustment: the viscosity could be adjusted according to different spray methods. Dilute with clean water if the viscosity is over high;
● Coating filtration: filtrate the coating with screen (100mesh) before using.

3.Application

● The spraying environment should be dry, well-ventilated, no smoking and fire. We suggest using dedicated spray gun, elevated tank and curing oven;
● The air compressor should be degreased, dewatered and equipped with water oil separator before using;
● Roll the coating at 30rpm speed before using to make sure there is no sediment, and filter with 100 mesh screen;
● Adjust atomization and oil pump capacity of the spraying gun; make sure the unit is clean and flat;
● Preheat the substrate to 35℃ and spray the primer. Dry it at temperature of 120℃~150℃ for 10min-15min. Keep the thickness of primer within 12μm-18μm;
● Spray top coating after the primer is dry and cooling to room temperature, then spray the top. Dry the unit at the temperature of 100℃~150℃ for 10~20 min, and gradually increase the temperature to 380℃~420℃. Keep for 10 min. Keep the thickness of top coat within 10μm~12μm. The thickness of two coat tally should be between 20μm~30μm;
● The oven (or the tunnel drier) must be well ventilated; otherwise, it will lead to color change of coating.

Product Message
社媒暂无评论
Chat Online 编辑模式下无法使用
Chat Online inputting...